An induction-motor speed estimator based on integral sliding-mode current control

Research output: Contribution to journalArticle

59 Citations (Scopus)

Abstract

This paper presents a speed-estimation method for the induction-motor (IM) drive that is based on a special current-control scheme called Integral Sliding-Mode Current Control (ISM-CC). Classic current control for the IM drive is done by regulating the d-q synchronous reference frame currents using PI controllers with or without a decoupling compensator. If a decoupling compensator is used, the speed and the motor parameters are needed to compute the decoupling voltages. Often, the speed (or the speed estimate) is not available, and the decoupling compensator is omitted; this leads to a degraded performance of the current controller. The ISM-CC scheme was developed for the decoupled control of the d-q currents and does not require the knowledge of the speed. In the ISM-CC, PI controllers act on simulated ideal plant models, and the resulting command voltages are complemented with voltages generated by SM controllers. It is shown that the SM controllers play the same role as the compensation voltages produced by a decoupling compensator. The speed estimator is constructed based on this observation-speed is estimated through algebraic calculations. This paper describes both the ISM-CC method and the speed estimator. Simulations and experimental results on a 1/4-hp three-phase IM confirm the validity of the method.

Original languageEnglish (US)
Pages (from-to)3414-3423
Number of pages10
JournalIEEE Transactions on Industrial Electronics
Volume56
Issue number9
DOIs
StatePublished - Sep 3 2009

Fingerprint

Electric current control
Sliding mode control
Induction motors
Controllers
Electric potential

All Science Journal Classification (ASJC) codes

  • Control and Systems Engineering
  • Electrical and Electronic Engineering

Cite this

@article{7eed306172504489afeacbae35045c7a,
title = "An induction-motor speed estimator based on integral sliding-mode current control",
abstract = "This paper presents a speed-estimation method for the induction-motor (IM) drive that is based on a special current-control scheme called Integral Sliding-Mode Current Control (ISM-CC). Classic current control for the IM drive is done by regulating the d-q synchronous reference frame currents using PI controllers with or without a decoupling compensator. If a decoupling compensator is used, the speed and the motor parameters are needed to compute the decoupling voltages. Often, the speed (or the speed estimate) is not available, and the decoupling compensator is omitted; this leads to a degraded performance of the current controller. The ISM-CC scheme was developed for the decoupled control of the d-q currents and does not require the knowledge of the speed. In the ISM-CC, PI controllers act on simulated ideal plant models, and the resulting command voltages are complemented with voltages generated by SM controllers. It is shown that the SM controllers play the same role as the compensation voltages produced by a decoupling compensator. The speed estimator is constructed based on this observation-speed is estimated through algebraic calculations. This paper describes both the ISM-CC method and the speed estimator. Simulations and experimental results on a 1/4-hp three-phase IM confirm the validity of the method.",
author = "Mihai Comanescu",
year = "2009",
month = "9",
day = "3",
doi = "10.1109/TIE.2009.2017554",
language = "English (US)",
volume = "56",
pages = "3414--3423",
journal = "IEEE Transactions on Industrial Electronics",
issn = "0278-0046",
publisher = "IEEE Industrial Electronics Society",
number = "9",

}

An induction-motor speed estimator based on integral sliding-mode current control. / Comanescu, Mihai.

In: IEEE Transactions on Industrial Electronics, Vol. 56, No. 9, 03.09.2009, p. 3414-3423.

Research output: Contribution to journalArticle

TY - JOUR

T1 - An induction-motor speed estimator based on integral sliding-mode current control

AU - Comanescu, Mihai

PY - 2009/9/3

Y1 - 2009/9/3

N2 - This paper presents a speed-estimation method for the induction-motor (IM) drive that is based on a special current-control scheme called Integral Sliding-Mode Current Control (ISM-CC). Classic current control for the IM drive is done by regulating the d-q synchronous reference frame currents using PI controllers with or without a decoupling compensator. If a decoupling compensator is used, the speed and the motor parameters are needed to compute the decoupling voltages. Often, the speed (or the speed estimate) is not available, and the decoupling compensator is omitted; this leads to a degraded performance of the current controller. The ISM-CC scheme was developed for the decoupled control of the d-q currents and does not require the knowledge of the speed. In the ISM-CC, PI controllers act on simulated ideal plant models, and the resulting command voltages are complemented with voltages generated by SM controllers. It is shown that the SM controllers play the same role as the compensation voltages produced by a decoupling compensator. The speed estimator is constructed based on this observation-speed is estimated through algebraic calculations. This paper describes both the ISM-CC method and the speed estimator. Simulations and experimental results on a 1/4-hp three-phase IM confirm the validity of the method.

AB - This paper presents a speed-estimation method for the induction-motor (IM) drive that is based on a special current-control scheme called Integral Sliding-Mode Current Control (ISM-CC). Classic current control for the IM drive is done by regulating the d-q synchronous reference frame currents using PI controllers with or without a decoupling compensator. If a decoupling compensator is used, the speed and the motor parameters are needed to compute the decoupling voltages. Often, the speed (or the speed estimate) is not available, and the decoupling compensator is omitted; this leads to a degraded performance of the current controller. The ISM-CC scheme was developed for the decoupled control of the d-q currents and does not require the knowledge of the speed. In the ISM-CC, PI controllers act on simulated ideal plant models, and the resulting command voltages are complemented with voltages generated by SM controllers. It is shown that the SM controllers play the same role as the compensation voltages produced by a decoupling compensator. The speed estimator is constructed based on this observation-speed is estimated through algebraic calculations. This paper describes both the ISM-CC method and the speed estimator. Simulations and experimental results on a 1/4-hp three-phase IM confirm the validity of the method.

UR - http://www.scopus.com/inward/record.url?scp=69349093568&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=69349093568&partnerID=8YFLogxK

U2 - 10.1109/TIE.2009.2017554

DO - 10.1109/TIE.2009.2017554

M3 - Article

AN - SCOPUS:69349093568

VL - 56

SP - 3414

EP - 3423

JO - IEEE Transactions on Industrial Electronics

JF - IEEE Transactions on Industrial Electronics

SN - 0278-0046

IS - 9

ER -