Effect of fuel properties on the bottom ash generation rate by a laboratory fluidized bed combustor

Peter L. Rozelle, Sarma V. Pisupati, Alan W. Scaroni

Research output: Contribution to journalArticle

6 Citations (Scopus)

Abstract

The fluidized bed combustion (FBC) process, used in power generation, can handle a variety of fuels. However, the range of fuels that can be accommodated by an FBC boiler system is affected by the ability of the fuel, sorbent, and ash-handling equipment to move the required solids through the boiler. Of specific interest is the bottom ash handling equipment, which must have sufficient capacity to remove ash from the system in order to maintain a constant bed inventory level, and must have sufficient capability to cool the ash well below the bed temperature. Quantification of a fuel's bottom ash removal requirements can be useful for plant design. The effect of fuel properties, on the rate of bottom ash production in a laboratory FBC test system was examined. The work used coal products ranging in ash content from 20 to 40+ wt. %. The system's classification of solids by particle size into flyash and bottom ash was characterized using a partition curve. Fuel sizing was compared to the partition curve, and fuels were fractionated by particle size. Fuel fractions in the size range characteristic of bottom ash were further analyzed for distributions of ash content with respect to specific gravity, using float sink tests. The fuel fractions were then ashed in a fixed bed. In each case, the highest ash content fraction produced ash with the coarsest size consist (characteristic of bottom ash). The lower ash content fractions were found to produce ash in the size range characteristic of flyash, suggesting that the high ash content fractions were largely responsible for the production of bottom ash. The contributions of the specific gravity fractions to the composite ash in the fuels were quantified. The fuels were fired in the laboratory test system. Fuels with higher amounts of high specific gravity particles, in the size ranges characteristic of bottom ash, were found to produce more bottom ash, indicating the potential utility of float sink methods in the prediction of bottom ash removal requirements.

Original languageEnglish (US)
Pages (from-to)144-151
Number of pages8
JournalJournal of Energy Resources Technology, Transactions of the ASME
Volume129
Issue number2
DOIs
StatePublished - Dec 1 2007

Fingerprint

Ashes
Coal Ash
Fluidized bed combustors
bottom ash
ash
Fluidized bed combustion
Ash handling
Density (specific gravity)
range size
combustion
gravity
Boilers
rate
laboratory
effect
Particle size
particle size

All Science Journal Classification (ASJC) codes

  • Renewable Energy, Sustainability and the Environment
  • Fuel Technology
  • Energy Engineering and Power Technology
  • Mechanical Engineering
  • Geochemistry and Petrology

Cite this

@article{69d113c1d92b4fbaafe90873bdcea50f,
title = "Effect of fuel properties on the bottom ash generation rate by a laboratory fluidized bed combustor",
abstract = "The fluidized bed combustion (FBC) process, used in power generation, can handle a variety of fuels. However, the range of fuels that can be accommodated by an FBC boiler system is affected by the ability of the fuel, sorbent, and ash-handling equipment to move the required solids through the boiler. Of specific interest is the bottom ash handling equipment, which must have sufficient capacity to remove ash from the system in order to maintain a constant bed inventory level, and must have sufficient capability to cool the ash well below the bed temperature. Quantification of a fuel's bottom ash removal requirements can be useful for plant design. The effect of fuel properties, on the rate of bottom ash production in a laboratory FBC test system was examined. The work used coal products ranging in ash content from 20 to 40+ wt. {\%}. The system's classification of solids by particle size into flyash and bottom ash was characterized using a partition curve. Fuel sizing was compared to the partition curve, and fuels were fractionated by particle size. Fuel fractions in the size range characteristic of bottom ash were further analyzed for distributions of ash content with respect to specific gravity, using float sink tests. The fuel fractions were then ashed in a fixed bed. In each case, the highest ash content fraction produced ash with the coarsest size consist (characteristic of bottom ash). The lower ash content fractions were found to produce ash in the size range characteristic of flyash, suggesting that the high ash content fractions were largely responsible for the production of bottom ash. The contributions of the specific gravity fractions to the composite ash in the fuels were quantified. The fuels were fired in the laboratory test system. Fuels with higher amounts of high specific gravity particles, in the size ranges characteristic of bottom ash, were found to produce more bottom ash, indicating the potential utility of float sink methods in the prediction of bottom ash removal requirements.",
author = "Rozelle, {Peter L.} and Pisupati, {Sarma V.} and Scaroni, {Alan W.}",
year = "2007",
month = "12",
day = "1",
doi = "10.1115/1.2719205",
language = "English (US)",
volume = "129",
pages = "144--151",
journal = "Journal of Energy Resources Technology, Transactions of the ASME",
issn = "0195-0738",
publisher = "American Society of Mechanical Engineers(ASME)",
number = "2",

}

Effect of fuel properties on the bottom ash generation rate by a laboratory fluidized bed combustor. / Rozelle, Peter L.; Pisupati, Sarma V.; Scaroni, Alan W.

In: Journal of Energy Resources Technology, Transactions of the ASME, Vol. 129, No. 2, 01.12.2007, p. 144-151.

Research output: Contribution to journalArticle

TY - JOUR

T1 - Effect of fuel properties on the bottom ash generation rate by a laboratory fluidized bed combustor

AU - Rozelle, Peter L.

AU - Pisupati, Sarma V.

AU - Scaroni, Alan W.

PY - 2007/12/1

Y1 - 2007/12/1

N2 - The fluidized bed combustion (FBC) process, used in power generation, can handle a variety of fuels. However, the range of fuels that can be accommodated by an FBC boiler system is affected by the ability of the fuel, sorbent, and ash-handling equipment to move the required solids through the boiler. Of specific interest is the bottom ash handling equipment, which must have sufficient capacity to remove ash from the system in order to maintain a constant bed inventory level, and must have sufficient capability to cool the ash well below the bed temperature. Quantification of a fuel's bottom ash removal requirements can be useful for plant design. The effect of fuel properties, on the rate of bottom ash production in a laboratory FBC test system was examined. The work used coal products ranging in ash content from 20 to 40+ wt. %. The system's classification of solids by particle size into flyash and bottom ash was characterized using a partition curve. Fuel sizing was compared to the partition curve, and fuels were fractionated by particle size. Fuel fractions in the size range characteristic of bottom ash were further analyzed for distributions of ash content with respect to specific gravity, using float sink tests. The fuel fractions were then ashed in a fixed bed. In each case, the highest ash content fraction produced ash with the coarsest size consist (characteristic of bottom ash). The lower ash content fractions were found to produce ash in the size range characteristic of flyash, suggesting that the high ash content fractions were largely responsible for the production of bottom ash. The contributions of the specific gravity fractions to the composite ash in the fuels were quantified. The fuels were fired in the laboratory test system. Fuels with higher amounts of high specific gravity particles, in the size ranges characteristic of bottom ash, were found to produce more bottom ash, indicating the potential utility of float sink methods in the prediction of bottom ash removal requirements.

AB - The fluidized bed combustion (FBC) process, used in power generation, can handle a variety of fuels. However, the range of fuels that can be accommodated by an FBC boiler system is affected by the ability of the fuel, sorbent, and ash-handling equipment to move the required solids through the boiler. Of specific interest is the bottom ash handling equipment, which must have sufficient capacity to remove ash from the system in order to maintain a constant bed inventory level, and must have sufficient capability to cool the ash well below the bed temperature. Quantification of a fuel's bottom ash removal requirements can be useful for plant design. The effect of fuel properties, on the rate of bottom ash production in a laboratory FBC test system was examined. The work used coal products ranging in ash content from 20 to 40+ wt. %. The system's classification of solids by particle size into flyash and bottom ash was characterized using a partition curve. Fuel sizing was compared to the partition curve, and fuels were fractionated by particle size. Fuel fractions in the size range characteristic of bottom ash were further analyzed for distributions of ash content with respect to specific gravity, using float sink tests. The fuel fractions were then ashed in a fixed bed. In each case, the highest ash content fraction produced ash with the coarsest size consist (characteristic of bottom ash). The lower ash content fractions were found to produce ash in the size range characteristic of flyash, suggesting that the high ash content fractions were largely responsible for the production of bottom ash. The contributions of the specific gravity fractions to the composite ash in the fuels were quantified. The fuels were fired in the laboratory test system. Fuels with higher amounts of high specific gravity particles, in the size ranges characteristic of bottom ash, were found to produce more bottom ash, indicating the potential utility of float sink methods in the prediction of bottom ash removal requirements.

UR - http://www.scopus.com/inward/record.url?scp=44649149522&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=44649149522&partnerID=8YFLogxK

U2 - 10.1115/1.2719205

DO - 10.1115/1.2719205

M3 - Article

AN - SCOPUS:44649149522

VL - 129

SP - 144

EP - 151

JO - Journal of Energy Resources Technology, Transactions of the ASME

JF - Journal of Energy Resources Technology, Transactions of the ASME

SN - 0195-0738

IS - 2

ER -