Electroless silver plating of 3D printed waveguide components by peristaltic pump driven system

A. Bal; D. G. Carey; F. A. Espinal; G. H. Huff

doi:10.1049/el.2018.7288

Electroless silver plating of 3D printed waveguide components by peristaltic pump driven system

A. Bal, D. G. Carey, F. A. Espinal, G. H. Huff

Research output: Contribution to journal › Article › peer-review

4 Scopus citations

Abstract

V-band waveguide components operating in 57-64 GHz ISM band is presented. Consumer-grade stereolithographic 3D printer is used to print these waveguide components with black-pigmented acrylate-based polymer. Electroless deposition of silver on these microwave components is achieved using an in-house system assembled with off-the-shelf components. This system is driven by a peristaltic pump, circling plating solution between silver bath and waveguide. Metal plated WR-15, 2-inch waveguide section offers average insertion coefficient of −0.35 dB. Trough waveguide section connected to rectangular waveguide through rectangular to trough waveguide transition is metal plated and offers average insertion coefficient of −1 dB. Silver deposited using the pump operated system offers potential of achieving comparable results as conventional dip coating technique.

Original language	English (US)
Pages (from-to)	100-102
Number of pages	3
Journal	Electronics Letters
Volume	55
Issue number	2
DOIs	https://doi.org/10.1049/el.2018.7288
State	Published - Jan 24 2019

All Science Journal Classification (ASJC) codes

Electrical and Electronic Engineering

Access to Document

10.1049/el.2018.7288

Cite this

@article{9949514cc1e2467ca4371934939b3c4a,

title = "Electroless silver plating of 3D printed waveguide components by peristaltic pump driven system",

abstract = "V-band waveguide components operating in 57-64 GHz ISM band is presented. Consumer-grade stereolithographic 3D printer is used to print these waveguide components with black-pigmented acrylate-based polymer. Electroless deposition of silver on these microwave components is achieved using an in-house system assembled with off-the-shelf components. This system is driven by a peristaltic pump, circling plating solution between silver bath and waveguide. Metal plated WR-15, 2-inch waveguide section offers average insertion coefficient of −0.35 dB. Trough waveguide section connected to rectangular waveguide through rectangular to trough waveguide transition is metal plated and offers average insertion coefficient of −1 dB. Silver deposited using the pump operated system offers potential of achieving comparable results as conventional dip coating technique.",

author = "A. Bal and Carey, {D. G.} and Espinal, {F. A.} and Huff, {G. H.}",

note = "Publisher Copyright: {\textcopyright} The Institution of Engineering and Technology 2019",

year = "2019",

month = jan,

day = "24",

doi = "10.1049/el.2018.7288",

language = "English (US)",

volume = "55",

pages = "100--102",

journal = "Electronics Letters",

issn = "0013-5194",

publisher = "Institution of Engineering and Technology",

number = "2",

}

TY - JOUR

T1 - Electroless silver plating of 3D printed waveguide components by peristaltic pump driven system

AU - Bal, A.

AU - Carey, D. G.

AU - Espinal, F. A.

AU - Huff, G. H.

N1 - Publisher Copyright: © The Institution of Engineering and Technology 2019

PY - 2019/1/24

Y1 - 2019/1/24

N2 - V-band waveguide components operating in 57-64 GHz ISM band is presented. Consumer-grade stereolithographic 3D printer is used to print these waveguide components with black-pigmented acrylate-based polymer. Electroless deposition of silver on these microwave components is achieved using an in-house system assembled with off-the-shelf components. This system is driven by a peristaltic pump, circling plating solution between silver bath and waveguide. Metal plated WR-15, 2-inch waveguide section offers average insertion coefficient of −0.35 dB. Trough waveguide section connected to rectangular waveguide through rectangular to trough waveguide transition is metal plated and offers average insertion coefficient of −1 dB. Silver deposited using the pump operated system offers potential of achieving comparable results as conventional dip coating technique.

AB - V-band waveguide components operating in 57-64 GHz ISM band is presented. Consumer-grade stereolithographic 3D printer is used to print these waveguide components with black-pigmented acrylate-based polymer. Electroless deposition of silver on these microwave components is achieved using an in-house system assembled with off-the-shelf components. This system is driven by a peristaltic pump, circling plating solution between silver bath and waveguide. Metal plated WR-15, 2-inch waveguide section offers average insertion coefficient of −0.35 dB. Trough waveguide section connected to rectangular waveguide through rectangular to trough waveguide transition is metal plated and offers average insertion coefficient of −1 dB. Silver deposited using the pump operated system offers potential of achieving comparable results as conventional dip coating technique.

UR - http://www.scopus.com/inward/record.url?scp=85060097541&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=85060097541&partnerID=8YFLogxK

U2 - 10.1049/el.2018.7288

DO - 10.1049/el.2018.7288

M3 - Article

AN - SCOPUS:85060097541

VL - 55

SP - 100

EP - 102

JO - Electronics Letters

JF - Electronics Letters

SN - 0013-5194

IS - 2

ER -

Electroless silver plating of 3D printed waveguide components by peristaltic pump driven system

Abstract

All Science Journal Classification (ASJC) codes

Access to Document

Other files and links

Fingerprint

Cite this