Entrance effects on diffused film-cooling holes

A. Kohli, K. A. Thole

Research output: Chapter in Book/Report/Conference proceedingConference contribution

8 Citations (Scopus)

Abstract

Film-cooling is a widely used method of prolonging blade life in high performance gas turbines and is implemented by injecting cold air through discrete holes on the blade surface. Most experimental research on filmcooling has been performed using round holes supplied by a stagnant plenum. This can be quite different from the actual turbine blade conditions in that a crossflow may be present whereby the internal channel Reynolds number could be as high as 90,000. This computational study uses a film-cooling hole that is inclined at 35° with respect to the mainstream and is diffused at the hole exit by 15°. An engine representative jet-to-mainstream density ratio of two was simulated. The test matrix consisted of fourteen different cases that were simulated for the two different blowing ratios in which the following effects were investigated: a) the effect of the orientation of the coolant supply channel relative to the cooling hole, b) the effect of the channel Reynolds number, and c) the effect of the metering length of the cool ing hole. Results showed that the orientation of the coolant supply had a large effect whereby the worst orientation, in terms of a reduced adiabatic effectiveness, was predicted when the channel supplying the cooling hole was perpendicular to the mainstream. For this particular orientation, higher laterally averaged effectiveness occurred at lower channel Reynolds numbers and with the hole having a short metering length.

Original languageEnglish (US)
Title of host publicationHeat Transfer; Electric Power; Industrial and Cogeneration
PublisherAmerican Society of Mechanical Engineers (ASME)
ISBN (Electronic)9780791878651
DOIs
StatePublished - Jan 1 1998
EventASME 1998 International Gas Turbine and Aeroengine Congress and Exhibition, GT 1998 - Stockholm, Sweden
Duration: Jun 2 1998Jun 5 1998

Publication series

NameProceedings of the ASME Turbo Expo
Volume4

Other

OtherASME 1998 International Gas Turbine and Aeroengine Congress and Exhibition, GT 1998
CountrySweden
CityStockholm
Period6/2/986/5/98

Fingerprint

Cooling
Reynolds number
Coolants
Turbomachine blades
Jet engines
Blow molding
Gas turbines
Turbines
Air

All Science Journal Classification (ASJC) codes

  • Engineering(all)

Cite this

Kohli, A., & Thole, K. A. (1998). Entrance effects on diffused film-cooling holes. In Heat Transfer; Electric Power; Industrial and Cogeneration (Proceedings of the ASME Turbo Expo; Vol. 4). American Society of Mechanical Engineers (ASME). https://doi.org/10.1115/98-GT-402
Kohli, A. ; Thole, K. A. / Entrance effects on diffused film-cooling holes. Heat Transfer; Electric Power; Industrial and Cogeneration. American Society of Mechanical Engineers (ASME), 1998. (Proceedings of the ASME Turbo Expo).
@inproceedings{08d795c6c3f34459bdeaaabdf546ce72,
title = "Entrance effects on diffused film-cooling holes",
abstract = "Film-cooling is a widely used method of prolonging blade life in high performance gas turbines and is implemented by injecting cold air through discrete holes on the blade surface. Most experimental research on filmcooling has been performed using round holes supplied by a stagnant plenum. This can be quite different from the actual turbine blade conditions in that a crossflow may be present whereby the internal channel Reynolds number could be as high as 90,000. This computational study uses a film-cooling hole that is inclined at 35° with respect to the mainstream and is diffused at the hole exit by 15°. An engine representative jet-to-mainstream density ratio of two was simulated. The test matrix consisted of fourteen different cases that were simulated for the two different blowing ratios in which the following effects were investigated: a) the effect of the orientation of the coolant supply channel relative to the cooling hole, b) the effect of the channel Reynolds number, and c) the effect of the metering length of the cool ing hole. Results showed that the orientation of the coolant supply had a large effect whereby the worst orientation, in terms of a reduced adiabatic effectiveness, was predicted when the channel supplying the cooling hole was perpendicular to the mainstream. For this particular orientation, higher laterally averaged effectiveness occurred at lower channel Reynolds numbers and with the hole having a short metering length.",
author = "A. Kohli and Thole, {K. A.}",
year = "1998",
month = "1",
day = "1",
doi = "10.1115/98-GT-402",
language = "English (US)",
series = "Proceedings of the ASME Turbo Expo",
publisher = "American Society of Mechanical Engineers (ASME)",
booktitle = "Heat Transfer; Electric Power; Industrial and Cogeneration",

}

Kohli, A & Thole, KA 1998, Entrance effects on diffused film-cooling holes. in Heat Transfer; Electric Power; Industrial and Cogeneration. Proceedings of the ASME Turbo Expo, vol. 4, American Society of Mechanical Engineers (ASME), ASME 1998 International Gas Turbine and Aeroengine Congress and Exhibition, GT 1998, Stockholm, Sweden, 6/2/98. https://doi.org/10.1115/98-GT-402

Entrance effects on diffused film-cooling holes. / Kohli, A.; Thole, K. A.

Heat Transfer; Electric Power; Industrial and Cogeneration. American Society of Mechanical Engineers (ASME), 1998. (Proceedings of the ASME Turbo Expo; Vol. 4).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

TY - GEN

T1 - Entrance effects on diffused film-cooling holes

AU - Kohli, A.

AU - Thole, K. A.

PY - 1998/1/1

Y1 - 1998/1/1

N2 - Film-cooling is a widely used method of prolonging blade life in high performance gas turbines and is implemented by injecting cold air through discrete holes on the blade surface. Most experimental research on filmcooling has been performed using round holes supplied by a stagnant plenum. This can be quite different from the actual turbine blade conditions in that a crossflow may be present whereby the internal channel Reynolds number could be as high as 90,000. This computational study uses a film-cooling hole that is inclined at 35° with respect to the mainstream and is diffused at the hole exit by 15°. An engine representative jet-to-mainstream density ratio of two was simulated. The test matrix consisted of fourteen different cases that were simulated for the two different blowing ratios in which the following effects were investigated: a) the effect of the orientation of the coolant supply channel relative to the cooling hole, b) the effect of the channel Reynolds number, and c) the effect of the metering length of the cool ing hole. Results showed that the orientation of the coolant supply had a large effect whereby the worst orientation, in terms of a reduced adiabatic effectiveness, was predicted when the channel supplying the cooling hole was perpendicular to the mainstream. For this particular orientation, higher laterally averaged effectiveness occurred at lower channel Reynolds numbers and with the hole having a short metering length.

AB - Film-cooling is a widely used method of prolonging blade life in high performance gas turbines and is implemented by injecting cold air through discrete holes on the blade surface. Most experimental research on filmcooling has been performed using round holes supplied by a stagnant plenum. This can be quite different from the actual turbine blade conditions in that a crossflow may be present whereby the internal channel Reynolds number could be as high as 90,000. This computational study uses a film-cooling hole that is inclined at 35° with respect to the mainstream and is diffused at the hole exit by 15°. An engine representative jet-to-mainstream density ratio of two was simulated. The test matrix consisted of fourteen different cases that were simulated for the two different blowing ratios in which the following effects were investigated: a) the effect of the orientation of the coolant supply channel relative to the cooling hole, b) the effect of the channel Reynolds number, and c) the effect of the metering length of the cool ing hole. Results showed that the orientation of the coolant supply had a large effect whereby the worst orientation, in terms of a reduced adiabatic effectiveness, was predicted when the channel supplying the cooling hole was perpendicular to the mainstream. For this particular orientation, higher laterally averaged effectiveness occurred at lower channel Reynolds numbers and with the hole having a short metering length.

UR - http://www.scopus.com/inward/record.url?scp=84973160976&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84973160976&partnerID=8YFLogxK

U2 - 10.1115/98-GT-402

DO - 10.1115/98-GT-402

M3 - Conference contribution

AN - SCOPUS:84973160976

T3 - Proceedings of the ASME Turbo Expo

BT - Heat Transfer; Electric Power; Industrial and Cogeneration

PB - American Society of Mechanical Engineers (ASME)

ER -

Kohli A, Thole KA. Entrance effects on diffused film-cooling holes. In Heat Transfer; Electric Power; Industrial and Cogeneration. American Society of Mechanical Engineers (ASME). 1998. (Proceedings of the ASME Turbo Expo). https://doi.org/10.1115/98-GT-402