Evaluation of pavement layer moduli using instrumentation measurements

Xiaochao Tang, Shelley Marie Stoffels, Angelica M. Palomino

Research output: Contribution to journalArticle

3 Citations (Scopus)

Abstract

Instrumentation embedded in pavements is increasingly being used to measure the critical responses and monitor performance of specially-constructed experimental pavement sections or in-service pavements under controlled wheel loading or live traffic. On the other hand, nondestructive tests (NDT), such as falling weight deflectometer (FWD) testing, are routinely performed to evaluate pavement layer structural properties based on deflections measured on the surface of the pavements. In cases where measurements from the pavement surface only are not sufficient to infer pavement layer modulus values, e.g. rolling wheel deflectometer (RWD) tests typically with only one deflection measurement or complex geometries, a procedure that combines measurements from the embedded instruments and surface deflections would provide an alternative to the traditional backcalculation of pavement layer moduli. This study presents an inverse analysis procedure integrating finite element (FE) models and a population-based optimization technique, Covariance Matrix Adaptation Evolution Strategy (CMA-ES), to determine the pavement layer structural properties. Tests using a lightweight deflectometer (LWD) were conducted on instrumented three-layer scaled flexible pavement test sections. The time histories of the LWD load, surface deflection underneath the LWD load, subgrade deflection and vertical stress were recorded and used in the inverse analysis. While the common practice in backcalculating pavement layer properties still assumes a static FWD load and makes use of only peak values of the load and deflections, dynamic analysis was conducted to simulate the impulse LWD load. Results of the inverse analysis show that consistent pavement layer properties can be obtained based on the LWD surface deflection data and measurements of the embedded instrumentation.

Original languageEnglish (US)
Pages (from-to)755-764
Number of pages10
JournalInternational Journal of Pavement Research and Technology
Volume6
Issue number6
DOIs
StatePublished - Nov 29 2013

Fingerprint

Pavements
Structural properties
Wheels
Deflection (structures)
Covariance matrix
Dynamic analysis
Loads (forces)
Geometry

All Science Journal Classification (ASJC) codes

  • Civil and Structural Engineering
  • Mechanics of Materials

Cite this

@article{724b4c9bac614aed81f42ff4c25011c0,
title = "Evaluation of pavement layer moduli using instrumentation measurements",
abstract = "Instrumentation embedded in pavements is increasingly being used to measure the critical responses and monitor performance of specially-constructed experimental pavement sections or in-service pavements under controlled wheel loading or live traffic. On the other hand, nondestructive tests (NDT), such as falling weight deflectometer (FWD) testing, are routinely performed to evaluate pavement layer structural properties based on deflections measured on the surface of the pavements. In cases where measurements from the pavement surface only are not sufficient to infer pavement layer modulus values, e.g. rolling wheel deflectometer (RWD) tests typically with only one deflection measurement or complex geometries, a procedure that combines measurements from the embedded instruments and surface deflections would provide an alternative to the traditional backcalculation of pavement layer moduli. This study presents an inverse analysis procedure integrating finite element (FE) models and a population-based optimization technique, Covariance Matrix Adaptation Evolution Strategy (CMA-ES), to determine the pavement layer structural properties. Tests using a lightweight deflectometer (LWD) were conducted on instrumented three-layer scaled flexible pavement test sections. The time histories of the LWD load, surface deflection underneath the LWD load, subgrade deflection and vertical stress were recorded and used in the inverse analysis. While the common practice in backcalculating pavement layer properties still assumes a static FWD load and makes use of only peak values of the load and deflections, dynamic analysis was conducted to simulate the impulse LWD load. Results of the inverse analysis show that consistent pavement layer properties can be obtained based on the LWD surface deflection data and measurements of the embedded instrumentation.",
author = "Xiaochao Tang and Stoffels, {Shelley Marie} and Palomino, {Angelica M.}",
year = "2013",
month = "11",
day = "29",
doi = "10.6135/ijprt.org.tw/2013.6(6).755",
language = "English (US)",
volume = "6",
pages = "755--764",
journal = "International Journal of Pavement Research and Technology",
issn = "1996-6814",
publisher = "Chinese Society of Pavement Engineering",
number = "6",

}

Evaluation of pavement layer moduli using instrumentation measurements. / Tang, Xiaochao; Stoffels, Shelley Marie; Palomino, Angelica M.

In: International Journal of Pavement Research and Technology, Vol. 6, No. 6, 29.11.2013, p. 755-764.

Research output: Contribution to journalArticle

TY - JOUR

T1 - Evaluation of pavement layer moduli using instrumentation measurements

AU - Tang, Xiaochao

AU - Stoffels, Shelley Marie

AU - Palomino, Angelica M.

PY - 2013/11/29

Y1 - 2013/11/29

N2 - Instrumentation embedded in pavements is increasingly being used to measure the critical responses and monitor performance of specially-constructed experimental pavement sections or in-service pavements under controlled wheel loading or live traffic. On the other hand, nondestructive tests (NDT), such as falling weight deflectometer (FWD) testing, are routinely performed to evaluate pavement layer structural properties based on deflections measured on the surface of the pavements. In cases where measurements from the pavement surface only are not sufficient to infer pavement layer modulus values, e.g. rolling wheel deflectometer (RWD) tests typically with only one deflection measurement or complex geometries, a procedure that combines measurements from the embedded instruments and surface deflections would provide an alternative to the traditional backcalculation of pavement layer moduli. This study presents an inverse analysis procedure integrating finite element (FE) models and a population-based optimization technique, Covariance Matrix Adaptation Evolution Strategy (CMA-ES), to determine the pavement layer structural properties. Tests using a lightweight deflectometer (LWD) were conducted on instrumented three-layer scaled flexible pavement test sections. The time histories of the LWD load, surface deflection underneath the LWD load, subgrade deflection and vertical stress were recorded and used in the inverse analysis. While the common practice in backcalculating pavement layer properties still assumes a static FWD load and makes use of only peak values of the load and deflections, dynamic analysis was conducted to simulate the impulse LWD load. Results of the inverse analysis show that consistent pavement layer properties can be obtained based on the LWD surface deflection data and measurements of the embedded instrumentation.

AB - Instrumentation embedded in pavements is increasingly being used to measure the critical responses and monitor performance of specially-constructed experimental pavement sections or in-service pavements under controlled wheel loading or live traffic. On the other hand, nondestructive tests (NDT), such as falling weight deflectometer (FWD) testing, are routinely performed to evaluate pavement layer structural properties based on deflections measured on the surface of the pavements. In cases where measurements from the pavement surface only are not sufficient to infer pavement layer modulus values, e.g. rolling wheel deflectometer (RWD) tests typically with only one deflection measurement or complex geometries, a procedure that combines measurements from the embedded instruments and surface deflections would provide an alternative to the traditional backcalculation of pavement layer moduli. This study presents an inverse analysis procedure integrating finite element (FE) models and a population-based optimization technique, Covariance Matrix Adaptation Evolution Strategy (CMA-ES), to determine the pavement layer structural properties. Tests using a lightweight deflectometer (LWD) were conducted on instrumented three-layer scaled flexible pavement test sections. The time histories of the LWD load, surface deflection underneath the LWD load, subgrade deflection and vertical stress were recorded and used in the inverse analysis. While the common practice in backcalculating pavement layer properties still assumes a static FWD load and makes use of only peak values of the load and deflections, dynamic analysis was conducted to simulate the impulse LWD load. Results of the inverse analysis show that consistent pavement layer properties can be obtained based on the LWD surface deflection data and measurements of the embedded instrumentation.

UR - http://www.scopus.com/inward/record.url?scp=84888243651&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84888243651&partnerID=8YFLogxK

U2 - 10.6135/ijprt.org.tw/2013.6(6).755

DO - 10.6135/ijprt.org.tw/2013.6(6).755

M3 - Article

VL - 6

SP - 755

EP - 764

JO - International Journal of Pavement Research and Technology

JF - International Journal of Pavement Research and Technology

SN - 1996-6814

IS - 6

ER -