Evaluation of uniformity of simultaneous powder deposition in multiple containers of different cross sections

X. Xie, Virendra Puri, A. S. Grader

Research output: Contribution to conferencePaper

Abstract

Spatial bulk density distribution of powder filled into multiple containers, which is very important both theoretically and practically, has not yet been fully examined. In this research, the second generation mass deposition tester (MDT-II) was used to investigate the uniformity of simultaneous powder deposition in three parallel cylindrical containers and three parallel toroidal containers, so as to study the effects of container locations, container shape, and feed shoe speed on powder deposition. The current results demonstrated that (1) center container vs. right container: for most locations, the right container had higher mean final mass values than the center container, but the quantitative differences were reduced with increase in the feed shoe speed for cylindrical containers; (2) 100 vs. 500 mm/s feed shoe speed for toroidal containers: except for 0° and 180° orientations, the mean final mass values were similar at the two speeds; (3) 100 vs. 500 mm/s feed shoe speed for cylindrical containers: 500 mm/s feed shoe speed resulted in higher mean final mass values than 100 mm/s feed shoe speed for most locations; (4) cylindrical container vs. toroidal container: generally, toroidal containers had lower measured mean final mass values, with some exceptions along certain orientations; and the higher the feed shoe speed, the larger the difference was between the final mass values of center toroidal and cylindrical containers.

Original languageEnglish (US)
Pages5803-5818
Number of pages16
StatePublished - Dec 1 2004
EventASAE Annual International Meeting 2004 - Ottawa, ON, Canada
Duration: Aug 1 2004Aug 4 2004

Other

OtherASAE Annual International Meeting 2004
CountryCanada
CityOttawa, ON
Period8/1/048/4/04

Fingerprint

Containers
Powders

All Science Journal Classification (ASJC) codes

  • Engineering(all)

Cite this

Xie, X., Puri, V., & Grader, A. S. (2004). Evaluation of uniformity of simultaneous powder deposition in multiple containers of different cross sections. 5803-5818. Paper presented at ASAE Annual International Meeting 2004, Ottawa, ON, Canada.
Xie, X. ; Puri, Virendra ; Grader, A. S. / Evaluation of uniformity of simultaneous powder deposition in multiple containers of different cross sections. Paper presented at ASAE Annual International Meeting 2004, Ottawa, ON, Canada.16 p.
@conference{eba970092d4d4588a51bad42f95254a9,
title = "Evaluation of uniformity of simultaneous powder deposition in multiple containers of different cross sections",
abstract = "Spatial bulk density distribution of powder filled into multiple containers, which is very important both theoretically and practically, has not yet been fully examined. In this research, the second generation mass deposition tester (MDT-II) was used to investigate the uniformity of simultaneous powder deposition in three parallel cylindrical containers and three parallel toroidal containers, so as to study the effects of container locations, container shape, and feed shoe speed on powder deposition. The current results demonstrated that (1) center container vs. right container: for most locations, the right container had higher mean final mass values than the center container, but the quantitative differences were reduced with increase in the feed shoe speed for cylindrical containers; (2) 100 vs. 500 mm/s feed shoe speed for toroidal containers: except for 0° and 180° orientations, the mean final mass values were similar at the two speeds; (3) 100 vs. 500 mm/s feed shoe speed for cylindrical containers: 500 mm/s feed shoe speed resulted in higher mean final mass values than 100 mm/s feed shoe speed for most locations; (4) cylindrical container vs. toroidal container: generally, toroidal containers had lower measured mean final mass values, with some exceptions along certain orientations; and the higher the feed shoe speed, the larger the difference was between the final mass values of center toroidal and cylindrical containers.",
author = "X. Xie and Virendra Puri and Grader, {A. S.}",
year = "2004",
month = "12",
day = "1",
language = "English (US)",
pages = "5803--5818",
note = "ASAE Annual International Meeting 2004 ; Conference date: 01-08-2004 Through 04-08-2004",

}

Xie, X, Puri, V & Grader, AS 2004, 'Evaluation of uniformity of simultaneous powder deposition in multiple containers of different cross sections', Paper presented at ASAE Annual International Meeting 2004, Ottawa, ON, Canada, 8/1/04 - 8/4/04 pp. 5803-5818.

Evaluation of uniformity of simultaneous powder deposition in multiple containers of different cross sections. / Xie, X.; Puri, Virendra; Grader, A. S.

2004. 5803-5818 Paper presented at ASAE Annual International Meeting 2004, Ottawa, ON, Canada.

Research output: Contribution to conferencePaper

TY - CONF

T1 - Evaluation of uniformity of simultaneous powder deposition in multiple containers of different cross sections

AU - Xie, X.

AU - Puri, Virendra

AU - Grader, A. S.

PY - 2004/12/1

Y1 - 2004/12/1

N2 - Spatial bulk density distribution of powder filled into multiple containers, which is very important both theoretically and practically, has not yet been fully examined. In this research, the second generation mass deposition tester (MDT-II) was used to investigate the uniformity of simultaneous powder deposition in three parallel cylindrical containers and three parallel toroidal containers, so as to study the effects of container locations, container shape, and feed shoe speed on powder deposition. The current results demonstrated that (1) center container vs. right container: for most locations, the right container had higher mean final mass values than the center container, but the quantitative differences were reduced with increase in the feed shoe speed for cylindrical containers; (2) 100 vs. 500 mm/s feed shoe speed for toroidal containers: except for 0° and 180° orientations, the mean final mass values were similar at the two speeds; (3) 100 vs. 500 mm/s feed shoe speed for cylindrical containers: 500 mm/s feed shoe speed resulted in higher mean final mass values than 100 mm/s feed shoe speed for most locations; (4) cylindrical container vs. toroidal container: generally, toroidal containers had lower measured mean final mass values, with some exceptions along certain orientations; and the higher the feed shoe speed, the larger the difference was between the final mass values of center toroidal and cylindrical containers.

AB - Spatial bulk density distribution of powder filled into multiple containers, which is very important both theoretically and practically, has not yet been fully examined. In this research, the second generation mass deposition tester (MDT-II) was used to investigate the uniformity of simultaneous powder deposition in three parallel cylindrical containers and three parallel toroidal containers, so as to study the effects of container locations, container shape, and feed shoe speed on powder deposition. The current results demonstrated that (1) center container vs. right container: for most locations, the right container had higher mean final mass values than the center container, but the quantitative differences were reduced with increase in the feed shoe speed for cylindrical containers; (2) 100 vs. 500 mm/s feed shoe speed for toroidal containers: except for 0° and 180° orientations, the mean final mass values were similar at the two speeds; (3) 100 vs. 500 mm/s feed shoe speed for cylindrical containers: 500 mm/s feed shoe speed resulted in higher mean final mass values than 100 mm/s feed shoe speed for most locations; (4) cylindrical container vs. toroidal container: generally, toroidal containers had lower measured mean final mass values, with some exceptions along certain orientations; and the higher the feed shoe speed, the larger the difference was between the final mass values of center toroidal and cylindrical containers.

UR - http://www.scopus.com/inward/record.url?scp=30144443289&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=30144443289&partnerID=8YFLogxK

M3 - Paper

AN - SCOPUS:30144443289

SP - 5803

EP - 5818

ER -

Xie X, Puri V, Grader AS. Evaluation of uniformity of simultaneous powder deposition in multiple containers of different cross sections. 2004. Paper presented at ASAE Annual International Meeting 2004, Ottawa, ON, Canada.