Hot-film wall shear probe measurements inside a ventricular assist device

J. T. Baldwin, J. M. Tarbell, S. Deutsch, D. B. Geselowitz, Gerson Rosenberg

Research output: Contribution to journalArticle

16 Citations (Scopus)

Abstract

Wall shear rates at eleven sites within the Penn State Electric Ventricular Assist Device (EVAD) were determined with the pump operating under conditions of 30 and 50 percent systolic duration and a mean flow rate of 5.8 L/min using a flushmounted hot-film probe. Probe calibrations were performed with the hot-film in two orientations relative to the flow direction: a standard orientation and an orientation in which the hot-film was rotated by 90 deg from the standard orientation. The magnitude and direction of the wall shear stress at each site within the EVAD were estimated from ensemble averaged voltage data recorded for similar standard and rotated film orientations. The results indicate that, during diastole the wall shear stress direction around the pump's periphery for both operating conditions is predominantly perpendicular to the inflow-outflow plane (in the direction of the pusher plate motion) and reaches a peak value of approximately 350 dynes/cm2. The highest wall shear stresses were found near the prosthetic aortic valve (inside the EVAD) under the 30percent systolic duration condition and are estimated to be as high as 2700 dynes/cm2. Peak shear stress values of 1400 dynes/cm2 were observed in the vicinity of the prosthetic mitral valve under both operating conditions. The results suggested that the valve regions are substantially more hemolytic than other wall regions of the EVAD; the magnitudes of the wall shear stresses are sensitive to operating conditions; and that wall shear in the direction of pusher plate motion can be significant.

Original languageEnglish (US)
Pages (from-to)326-333
Number of pages8
JournalJournal of Biomechanical Engineering
Volume110
Issue number4
DOIs
StatePublished - Jan 1 1988

Fingerprint

Heart-Assist Devices
Shear walls
Shear stress
Prosthetics
Pumps
Diastole
Aortic Valve
Mitral Valve
Shear deformation
Calibration
Flow rate
Direction compound
Electric potential

All Science Journal Classification (ASJC) codes

  • Biomedical Engineering
  • Physiology (medical)

Cite this

Baldwin, J. T. ; Tarbell, J. M. ; Deutsch, S. ; Geselowitz, D. B. ; Rosenberg, Gerson. / Hot-film wall shear probe measurements inside a ventricular assist device. In: Journal of Biomechanical Engineering. 1988 ; Vol. 110, No. 4. pp. 326-333.
@article{712ed07a3df64199b151dfd1a9b50307,
title = "Hot-film wall shear probe measurements inside a ventricular assist device",
abstract = "Wall shear rates at eleven sites within the Penn State Electric Ventricular Assist Device (EVAD) were determined with the pump operating under conditions of 30 and 50 percent systolic duration and a mean flow rate of 5.8 L/min using a flushmounted hot-film probe. Probe calibrations were performed with the hot-film in two orientations relative to the flow direction: a standard orientation and an orientation in which the hot-film was rotated by 90 deg from the standard orientation. The magnitude and direction of the wall shear stress at each site within the EVAD were estimated from ensemble averaged voltage data recorded for similar standard and rotated film orientations. The results indicate that, during diastole the wall shear stress direction around the pump's periphery for both operating conditions is predominantly perpendicular to the inflow-outflow plane (in the direction of the pusher plate motion) and reaches a peak value of approximately 350 dynes/cm2. The highest wall shear stresses were found near the prosthetic aortic valve (inside the EVAD) under the 30percent systolic duration condition and are estimated to be as high as 2700 dynes/cm2. Peak shear stress values of 1400 dynes/cm2 were observed in the vicinity of the prosthetic mitral valve under both operating conditions. The results suggested that the valve regions are substantially more hemolytic than other wall regions of the EVAD; the magnitudes of the wall shear stresses are sensitive to operating conditions; and that wall shear in the direction of pusher plate motion can be significant.",
author = "Baldwin, {J. T.} and Tarbell, {J. M.} and S. Deutsch and Geselowitz, {D. B.} and Gerson Rosenberg",
year = "1988",
month = "1",
day = "1",
doi = "10.1115/1.3108449",
language = "English (US)",
volume = "110",
pages = "326--333",
journal = "Journal of Biomechanical Engineering",
issn = "0148-0731",
publisher = "American Society of Mechanical Engineers(ASME)",
number = "4",

}

Hot-film wall shear probe measurements inside a ventricular assist device. / Baldwin, J. T.; Tarbell, J. M.; Deutsch, S.; Geselowitz, D. B.; Rosenberg, Gerson.

In: Journal of Biomechanical Engineering, Vol. 110, No. 4, 01.01.1988, p. 326-333.

Research output: Contribution to journalArticle

TY - JOUR

T1 - Hot-film wall shear probe measurements inside a ventricular assist device

AU - Baldwin, J. T.

AU - Tarbell, J. M.

AU - Deutsch, S.

AU - Geselowitz, D. B.

AU - Rosenberg, Gerson

PY - 1988/1/1

Y1 - 1988/1/1

N2 - Wall shear rates at eleven sites within the Penn State Electric Ventricular Assist Device (EVAD) were determined with the pump operating under conditions of 30 and 50 percent systolic duration and a mean flow rate of 5.8 L/min using a flushmounted hot-film probe. Probe calibrations were performed with the hot-film in two orientations relative to the flow direction: a standard orientation and an orientation in which the hot-film was rotated by 90 deg from the standard orientation. The magnitude and direction of the wall shear stress at each site within the EVAD were estimated from ensemble averaged voltage data recorded for similar standard and rotated film orientations. The results indicate that, during diastole the wall shear stress direction around the pump's periphery for both operating conditions is predominantly perpendicular to the inflow-outflow plane (in the direction of the pusher plate motion) and reaches a peak value of approximately 350 dynes/cm2. The highest wall shear stresses were found near the prosthetic aortic valve (inside the EVAD) under the 30percent systolic duration condition and are estimated to be as high as 2700 dynes/cm2. Peak shear stress values of 1400 dynes/cm2 were observed in the vicinity of the prosthetic mitral valve under both operating conditions. The results suggested that the valve regions are substantially more hemolytic than other wall regions of the EVAD; the magnitudes of the wall shear stresses are sensitive to operating conditions; and that wall shear in the direction of pusher plate motion can be significant.

AB - Wall shear rates at eleven sites within the Penn State Electric Ventricular Assist Device (EVAD) were determined with the pump operating under conditions of 30 and 50 percent systolic duration and a mean flow rate of 5.8 L/min using a flushmounted hot-film probe. Probe calibrations were performed with the hot-film in two orientations relative to the flow direction: a standard orientation and an orientation in which the hot-film was rotated by 90 deg from the standard orientation. The magnitude and direction of the wall shear stress at each site within the EVAD were estimated from ensemble averaged voltage data recorded for similar standard and rotated film orientations. The results indicate that, during diastole the wall shear stress direction around the pump's periphery for both operating conditions is predominantly perpendicular to the inflow-outflow plane (in the direction of the pusher plate motion) and reaches a peak value of approximately 350 dynes/cm2. The highest wall shear stresses were found near the prosthetic aortic valve (inside the EVAD) under the 30percent systolic duration condition and are estimated to be as high as 2700 dynes/cm2. Peak shear stress values of 1400 dynes/cm2 were observed in the vicinity of the prosthetic mitral valve under both operating conditions. The results suggested that the valve regions are substantially more hemolytic than other wall regions of the EVAD; the magnitudes of the wall shear stresses are sensitive to operating conditions; and that wall shear in the direction of pusher plate motion can be significant.

UR - http://www.scopus.com/inward/record.url?scp=0024118967&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=0024118967&partnerID=8YFLogxK

U2 - 10.1115/1.3108449

DO - 10.1115/1.3108449

M3 - Article

VL - 110

SP - 326

EP - 333

JO - Journal of Biomechanical Engineering

JF - Journal of Biomechanical Engineering

SN - 0148-0731

IS - 4

ER -