Investigation of Geometry and Current Density Effects in a Pulsed Electrothermal Plasma Source Using a 2-D Simulation Model

Micah J. Esmond, Leigh Winfrey

Research output: Contribution to journalArticle

3 Citations (Scopus)

Abstract

Electrothermal (ET) plasma discharges have application to mass acceleration technologies relevant to military ballistics and magnetic confinement fusion reactor operation. ET plasma discharges are initiated in capillary geometries by passing large currents (order of tens of kiloamperes) along the capillary axis. A partially ionized plasma then forms and radiates heat to the capillary walls inducing ablation. Ablated particles enter the capillary plasma source and cause a pressure surge that can propel pellets to velocities exceeding 2 km/s. These devices present several advantages over other mass accelerator technologies due to their simple design and ability to achieve high projectile launch frequencies. In order to investigate the operation of ET plasma discharges in more detail than previously possible, a 2-D, multifluid model has been developed to simulate the plasma-fluid dynamics that develop in these devices during operation. In this paper, the 2-D simulation model is used to investigate the effect of source geometry and current density on discharge characteristics. Peak pressure and electric field magnitudes for pulsed discharge operation are shown to scale well with theoretical and empirical scaling laws for steady-state discharge operation. The pulse shape of the source internal pressure is shown to change significantly with increasing source radius. The behavior of other plasma parameters is investigated. In addition, observations of the departure from the ablation-controlled arc regime are presented. This analysis suggests that, for the current pulse length investigated, source radii higher than 4 mm require significantly more current density in order to produce sufficient ablation to stabilize the plasma discharge.

Original languageEnglish (US)
Article number7782400
Pages (from-to)121-128
Number of pages8
JournalIEEE Transactions on Plasma Science
Volume45
Issue number1
DOIs
StatePublished - Jan 1 2017

Fingerprint

plasma jets
current density
ablation
geometry
simulation
radii
internal pressure
fusion reactors
fluid dynamics
pulses
pressure distribution
pellets
scaling laws
ballistics
projectiles
accelerators
arcs
heat
electric fields
causes

All Science Journal Classification (ASJC) codes

  • Nuclear and High Energy Physics
  • Condensed Matter Physics

Cite this

@article{0912fa5cf87c401eb9c01369eb67a02e,
title = "Investigation of Geometry and Current Density Effects in a Pulsed Electrothermal Plasma Source Using a 2-D Simulation Model",
abstract = "Electrothermal (ET) plasma discharges have application to mass acceleration technologies relevant to military ballistics and magnetic confinement fusion reactor operation. ET plasma discharges are initiated in capillary geometries by passing large currents (order of tens of kiloamperes) along the capillary axis. A partially ionized plasma then forms and radiates heat to the capillary walls inducing ablation. Ablated particles enter the capillary plasma source and cause a pressure surge that can propel pellets to velocities exceeding 2 km/s. These devices present several advantages over other mass accelerator technologies due to their simple design and ability to achieve high projectile launch frequencies. In order to investigate the operation of ET plasma discharges in more detail than previously possible, a 2-D, multifluid model has been developed to simulate the plasma-fluid dynamics that develop in these devices during operation. In this paper, the 2-D simulation model is used to investigate the effect of source geometry and current density on discharge characteristics. Peak pressure and electric field magnitudes for pulsed discharge operation are shown to scale well with theoretical and empirical scaling laws for steady-state discharge operation. The pulse shape of the source internal pressure is shown to change significantly with increasing source radius. The behavior of other plasma parameters is investigated. In addition, observations of the departure from the ablation-controlled arc regime are presented. This analysis suggests that, for the current pulse length investigated, source radii higher than 4 mm require significantly more current density in order to produce sufficient ablation to stabilize the plasma discharge.",
author = "Esmond, {Micah J.} and Leigh Winfrey",
year = "2017",
month = "1",
day = "1",
doi = "10.1109/TPS.2016.2633475",
language = "English (US)",
volume = "45",
pages = "121--128",
journal = "IEEE Transactions on Plasma Science",
issn = "0093-3813",
publisher = "Institute of Electrical and Electronics Engineers Inc.",
number = "1",

}

Investigation of Geometry and Current Density Effects in a Pulsed Electrothermal Plasma Source Using a 2-D Simulation Model. / Esmond, Micah J.; Winfrey, Leigh.

In: IEEE Transactions on Plasma Science, Vol. 45, No. 1, 7782400, 01.01.2017, p. 121-128.

Research output: Contribution to journalArticle

TY - JOUR

T1 - Investigation of Geometry and Current Density Effects in a Pulsed Electrothermal Plasma Source Using a 2-D Simulation Model

AU - Esmond, Micah J.

AU - Winfrey, Leigh

PY - 2017/1/1

Y1 - 2017/1/1

N2 - Electrothermal (ET) plasma discharges have application to mass acceleration technologies relevant to military ballistics and magnetic confinement fusion reactor operation. ET plasma discharges are initiated in capillary geometries by passing large currents (order of tens of kiloamperes) along the capillary axis. A partially ionized plasma then forms and radiates heat to the capillary walls inducing ablation. Ablated particles enter the capillary plasma source and cause a pressure surge that can propel pellets to velocities exceeding 2 km/s. These devices present several advantages over other mass accelerator technologies due to their simple design and ability to achieve high projectile launch frequencies. In order to investigate the operation of ET plasma discharges in more detail than previously possible, a 2-D, multifluid model has been developed to simulate the plasma-fluid dynamics that develop in these devices during operation. In this paper, the 2-D simulation model is used to investigate the effect of source geometry and current density on discharge characteristics. Peak pressure and electric field magnitudes for pulsed discharge operation are shown to scale well with theoretical and empirical scaling laws for steady-state discharge operation. The pulse shape of the source internal pressure is shown to change significantly with increasing source radius. The behavior of other plasma parameters is investigated. In addition, observations of the departure from the ablation-controlled arc regime are presented. This analysis suggests that, for the current pulse length investigated, source radii higher than 4 mm require significantly more current density in order to produce sufficient ablation to stabilize the plasma discharge.

AB - Electrothermal (ET) plasma discharges have application to mass acceleration technologies relevant to military ballistics and magnetic confinement fusion reactor operation. ET plasma discharges are initiated in capillary geometries by passing large currents (order of tens of kiloamperes) along the capillary axis. A partially ionized plasma then forms and radiates heat to the capillary walls inducing ablation. Ablated particles enter the capillary plasma source and cause a pressure surge that can propel pellets to velocities exceeding 2 km/s. These devices present several advantages over other mass accelerator technologies due to their simple design and ability to achieve high projectile launch frequencies. In order to investigate the operation of ET plasma discharges in more detail than previously possible, a 2-D, multifluid model has been developed to simulate the plasma-fluid dynamics that develop in these devices during operation. In this paper, the 2-D simulation model is used to investigate the effect of source geometry and current density on discharge characteristics. Peak pressure and electric field magnitudes for pulsed discharge operation are shown to scale well with theoretical and empirical scaling laws for steady-state discharge operation. The pulse shape of the source internal pressure is shown to change significantly with increasing source radius. The behavior of other plasma parameters is investigated. In addition, observations of the departure from the ablation-controlled arc regime are presented. This analysis suggests that, for the current pulse length investigated, source radii higher than 4 mm require significantly more current density in order to produce sufficient ablation to stabilize the plasma discharge.

UR - http://www.scopus.com/inward/record.url?scp=85006867182&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=85006867182&partnerID=8YFLogxK

U2 - 10.1109/TPS.2016.2633475

DO - 10.1109/TPS.2016.2633475

M3 - Article

AN - SCOPUS:85006867182

VL - 45

SP - 121

EP - 128

JO - IEEE Transactions on Plasma Science

JF - IEEE Transactions on Plasma Science

SN - 0093-3813

IS - 1

M1 - 7782400

ER -