Measurement and analysis of the pressure drop in a vertical annulus in a simulated air drilling operation

S. B. Supon, Michael A. Adewumi, N. Fairchild

Research output: Chapter in Book/Report/Conference proceedingConference contribution

4 Citations (Scopus)

Abstract

It is important to immediately clear cuttings from the face of the bit and to efficiently carry them to the surface in any drilling operation. Cuttings removal is especially critical in air drilling operations because of the relatively low viscosity of the gas compared to drilling mud. Air can effectively clear and remove cuttings, however, if the proper volumetric flow rate and injection pressure are used. One important feature of pneumatic conveying of solid particles in vertical pipes is that pressure drop initially decreases as the air velocity decreases, reaches a minimum, and then increases with further drops in air velocity. Eventually, the air flow can attain such a low velocity that the result is a sharp increase in pressure drop often accompanied by flow instabilities and vibration. The purpose of this study was to experimentally verify the presence of this minimum pressure drop in a simulated air drilling operation and to accurately determine it. The eventual goal is to develop a predictive capability for the velocity that yields this minimum pressure drop since this is an important parameter in optimizing the power requirements. A plexiglass wellbore model was constructed with air and sand feed lines at the bottom. The air-sand mixture flowed through a cyclone at the top to separate the two components and then recycled back into the feed line at the bottom. The pressure drop across the wellbore model was measured at various sand feed rates and air velocities. One of the findings of this study is that a minimum pressure drop does indeed occur at all sand feed rates as the air velocity decreases. We also found that there is a velocity at which the air moves too' slow to lift any of the particles. No more pressure readings are possible when air is moving at the choking velocity. This study is the first in a series of studies designed to foster a better understanding of the air drilling process. Our goal is to better understand the mechanics of air drilling and, ultimately, to be able to select the proper surface equipment for an optimized operation.

Original languageEnglish (US)
Title of host publicationSociety of Petroleum Engineers - SPE Eastern Regional Meeting, ERM 1987
PublisherSociety of Petroleum Engineers (SPE)
Pages119-126
Number of pages8
ISBN (Electronic)9781555635916
StatePublished - Jan 1 1987
EventSPE Eastern Regional Meeting, ERM 1987 - Pittsburgh, United States
Duration: Oct 21 1987Oct 23 1987

Publication series

NameSPE Eastern Regional Meeting
Volume1987-October

Other

OtherSPE Eastern Regional Meeting, ERM 1987
CountryUnited States
CityPittsburgh
Period10/21/8710/23/87

Fingerprint

Pressure drop
Drilling
Air
Sand
Drilling fluids
Conveying
Pneumatics
Mechanics
Pipe
Flow rate
Viscosity

All Science Journal Classification (ASJC) codes

  • Engineering(all)

Cite this

Supon, S. B., Adewumi, M. A., & Fairchild, N. (1987). Measurement and analysis of the pressure drop in a vertical annulus in a simulated air drilling operation. In Society of Petroleum Engineers - SPE Eastern Regional Meeting, ERM 1987 (pp. 119-126). (SPE Eastern Regional Meeting; Vol. 1987-October). Society of Petroleum Engineers (SPE).
Supon, S. B. ; Adewumi, Michael A. ; Fairchild, N. / Measurement and analysis of the pressure drop in a vertical annulus in a simulated air drilling operation. Society of Petroleum Engineers - SPE Eastern Regional Meeting, ERM 1987. Society of Petroleum Engineers (SPE), 1987. pp. 119-126 (SPE Eastern Regional Meeting).
@inproceedings{c9043fce809b4c4da0d65b7e32173a62,
title = "Measurement and analysis of the pressure drop in a vertical annulus in a simulated air drilling operation",
abstract = "It is important to immediately clear cuttings from the face of the bit and to efficiently carry them to the surface in any drilling operation. Cuttings removal is especially critical in air drilling operations because of the relatively low viscosity of the gas compared to drilling mud. Air can effectively clear and remove cuttings, however, if the proper volumetric flow rate and injection pressure are used. One important feature of pneumatic conveying of solid particles in vertical pipes is that pressure drop initially decreases as the air velocity decreases, reaches a minimum, and then increases with further drops in air velocity. Eventually, the air flow can attain such a low velocity that the result is a sharp increase in pressure drop often accompanied by flow instabilities and vibration. The purpose of this study was to experimentally verify the presence of this minimum pressure drop in a simulated air drilling operation and to accurately determine it. The eventual goal is to develop a predictive capability for the velocity that yields this minimum pressure drop since this is an important parameter in optimizing the power requirements. A plexiglass wellbore model was constructed with air and sand feed lines at the bottom. The air-sand mixture flowed through a cyclone at the top to separate the two components and then recycled back into the feed line at the bottom. The pressure drop across the wellbore model was measured at various sand feed rates and air velocities. One of the findings of this study is that a minimum pressure drop does indeed occur at all sand feed rates as the air velocity decreases. We also found that there is a velocity at which the air moves too' slow to lift any of the particles. No more pressure readings are possible when air is moving at the choking velocity. This study is the first in a series of studies designed to foster a better understanding of the air drilling process. Our goal is to better understand the mechanics of air drilling and, ultimately, to be able to select the proper surface equipment for an optimized operation.",
author = "Supon, {S. B.} and Adewumi, {Michael A.} and N. Fairchild",
year = "1987",
month = "1",
day = "1",
language = "English (US)",
series = "SPE Eastern Regional Meeting",
publisher = "Society of Petroleum Engineers (SPE)",
pages = "119--126",
booktitle = "Society of Petroleum Engineers - SPE Eastern Regional Meeting, ERM 1987",
address = "United States",

}

Supon, SB, Adewumi, MA & Fairchild, N 1987, Measurement and analysis of the pressure drop in a vertical annulus in a simulated air drilling operation. in Society of Petroleum Engineers - SPE Eastern Regional Meeting, ERM 1987. SPE Eastern Regional Meeting, vol. 1987-October, Society of Petroleum Engineers (SPE), pp. 119-126, SPE Eastern Regional Meeting, ERM 1987, Pittsburgh, United States, 10/21/87.

Measurement and analysis of the pressure drop in a vertical annulus in a simulated air drilling operation. / Supon, S. B.; Adewumi, Michael A.; Fairchild, N.

Society of Petroleum Engineers - SPE Eastern Regional Meeting, ERM 1987. Society of Petroleum Engineers (SPE), 1987. p. 119-126 (SPE Eastern Regional Meeting; Vol. 1987-October).

Research output: Chapter in Book/Report/Conference proceedingConference contribution

TY - GEN

T1 - Measurement and analysis of the pressure drop in a vertical annulus in a simulated air drilling operation

AU - Supon, S. B.

AU - Adewumi, Michael A.

AU - Fairchild, N.

PY - 1987/1/1

Y1 - 1987/1/1

N2 - It is important to immediately clear cuttings from the face of the bit and to efficiently carry them to the surface in any drilling operation. Cuttings removal is especially critical in air drilling operations because of the relatively low viscosity of the gas compared to drilling mud. Air can effectively clear and remove cuttings, however, if the proper volumetric flow rate and injection pressure are used. One important feature of pneumatic conveying of solid particles in vertical pipes is that pressure drop initially decreases as the air velocity decreases, reaches a minimum, and then increases with further drops in air velocity. Eventually, the air flow can attain such a low velocity that the result is a sharp increase in pressure drop often accompanied by flow instabilities and vibration. The purpose of this study was to experimentally verify the presence of this minimum pressure drop in a simulated air drilling operation and to accurately determine it. The eventual goal is to develop a predictive capability for the velocity that yields this minimum pressure drop since this is an important parameter in optimizing the power requirements. A plexiglass wellbore model was constructed with air and sand feed lines at the bottom. The air-sand mixture flowed through a cyclone at the top to separate the two components and then recycled back into the feed line at the bottom. The pressure drop across the wellbore model was measured at various sand feed rates and air velocities. One of the findings of this study is that a minimum pressure drop does indeed occur at all sand feed rates as the air velocity decreases. We also found that there is a velocity at which the air moves too' slow to lift any of the particles. No more pressure readings are possible when air is moving at the choking velocity. This study is the first in a series of studies designed to foster a better understanding of the air drilling process. Our goal is to better understand the mechanics of air drilling and, ultimately, to be able to select the proper surface equipment for an optimized operation.

AB - It is important to immediately clear cuttings from the face of the bit and to efficiently carry them to the surface in any drilling operation. Cuttings removal is especially critical in air drilling operations because of the relatively low viscosity of the gas compared to drilling mud. Air can effectively clear and remove cuttings, however, if the proper volumetric flow rate and injection pressure are used. One important feature of pneumatic conveying of solid particles in vertical pipes is that pressure drop initially decreases as the air velocity decreases, reaches a minimum, and then increases with further drops in air velocity. Eventually, the air flow can attain such a low velocity that the result is a sharp increase in pressure drop often accompanied by flow instabilities and vibration. The purpose of this study was to experimentally verify the presence of this minimum pressure drop in a simulated air drilling operation and to accurately determine it. The eventual goal is to develop a predictive capability for the velocity that yields this minimum pressure drop since this is an important parameter in optimizing the power requirements. A plexiglass wellbore model was constructed with air and sand feed lines at the bottom. The air-sand mixture flowed through a cyclone at the top to separate the two components and then recycled back into the feed line at the bottom. The pressure drop across the wellbore model was measured at various sand feed rates and air velocities. One of the findings of this study is that a minimum pressure drop does indeed occur at all sand feed rates as the air velocity decreases. We also found that there is a velocity at which the air moves too' slow to lift any of the particles. No more pressure readings are possible when air is moving at the choking velocity. This study is the first in a series of studies designed to foster a better understanding of the air drilling process. Our goal is to better understand the mechanics of air drilling and, ultimately, to be able to select the proper surface equipment for an optimized operation.

UR - http://www.scopus.com/inward/record.url?scp=84918674006&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84918674006&partnerID=8YFLogxK

M3 - Conference contribution

T3 - SPE Eastern Regional Meeting

SP - 119

EP - 126

BT - Society of Petroleum Engineers - SPE Eastern Regional Meeting, ERM 1987

PB - Society of Petroleum Engineers (SPE)

ER -

Supon SB, Adewumi MA, Fairchild N. Measurement and analysis of the pressure drop in a vertical annulus in a simulated air drilling operation. In Society of Petroleum Engineers - SPE Eastern Regional Meeting, ERM 1987. Society of Petroleum Engineers (SPE). 1987. p. 119-126. (SPE Eastern Regional Meeting).