Micromechanics of multiaxial plasticity of DP600: Experiments and microstructural deformation modeling

Shipin Qin, Ross McLendon, Victor Oancea, Allison M. Beese

Research output: Contribution to journalArticle

1 Citation (Scopus)

Abstract

Multiaxial plasticity behavior of Dual Phase (DP) 600 steel was evaluated through macroscopic testing and predicted through both continuum and micromechanics simulations. The stress state dependent mechanical properties of the material were examined through multiaxial loading under five stress states. The proposed continuum plasticity model was found to accurately predict the multiaxial mechanical response of the material through macroscopic simulations. The microstructure of DP600 contains a relatively soft ferrite matrix and relatively hard martensite particles, suggesting a more complex deformation behavior at the microscale compared to single phase materials. To understand the deformation mechanisms, a representative volume element (RVE) model based on the observed microstructures was built, which was able to predict the macroscopic multiaxial plasticity behavior of the material from the microstructural level. The local deformation inhomogeneity and stress states were also examined through this RVE model. The simulation results showed that in the DP steel studied, closely situated martensite particles increased the local plastic strain and stress triaxiality of the ferrite between them, with no trend for Lode angle parameter.

Original languageEnglish (US)
Pages (from-to)168-178
Number of pages11
JournalMaterials Science and Engineering A
Volume721
DOIs
StatePublished - Apr 4 2018

Fingerprint

micromechanics
Micromechanics
plastic properties
Plasticity
Steel
martensite
Martensite
Ferrite
ferrites
Experiments
steels
continuums
triaxial stresses
microstructure
Microstructure
simulation
microbalances
Plastic deformation
inhomogeneity
plastics

All Science Journal Classification (ASJC) codes

  • Materials Science(all)
  • Condensed Matter Physics
  • Mechanics of Materials
  • Mechanical Engineering

Cite this

@article{2c7a06b6c6f0435b9b8d9b7a14d43257,
title = "Micromechanics of multiaxial plasticity of DP600: Experiments and microstructural deformation modeling",
abstract = "Multiaxial plasticity behavior of Dual Phase (DP) 600 steel was evaluated through macroscopic testing and predicted through both continuum and micromechanics simulations. The stress state dependent mechanical properties of the material were examined through multiaxial loading under five stress states. The proposed continuum plasticity model was found to accurately predict the multiaxial mechanical response of the material through macroscopic simulations. The microstructure of DP600 contains a relatively soft ferrite matrix and relatively hard martensite particles, suggesting a more complex deformation behavior at the microscale compared to single phase materials. To understand the deformation mechanisms, a representative volume element (RVE) model based on the observed microstructures was built, which was able to predict the macroscopic multiaxial plasticity behavior of the material from the microstructural level. The local deformation inhomogeneity and stress states were also examined through this RVE model. The simulation results showed that in the DP steel studied, closely situated martensite particles increased the local plastic strain and stress triaxiality of the ferrite between them, with no trend for Lode angle parameter.",
author = "Shipin Qin and Ross McLendon and Victor Oancea and Beese, {Allison M.}",
year = "2018",
month = "4",
day = "4",
doi = "10.1016/j.msea.2018.02.078",
language = "English (US)",
volume = "721",
pages = "168--178",
journal = "Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing",
issn = "0921-5093",
publisher = "Elsevier BV",

}

Micromechanics of multiaxial plasticity of DP600 : Experiments and microstructural deformation modeling. / Qin, Shipin; McLendon, Ross; Oancea, Victor; Beese, Allison M.

In: Materials Science and Engineering A, Vol. 721, 04.04.2018, p. 168-178.

Research output: Contribution to journalArticle

TY - JOUR

T1 - Micromechanics of multiaxial plasticity of DP600

T2 - Experiments and microstructural deformation modeling

AU - Qin, Shipin

AU - McLendon, Ross

AU - Oancea, Victor

AU - Beese, Allison M.

PY - 2018/4/4

Y1 - 2018/4/4

N2 - Multiaxial plasticity behavior of Dual Phase (DP) 600 steel was evaluated through macroscopic testing and predicted through both continuum and micromechanics simulations. The stress state dependent mechanical properties of the material were examined through multiaxial loading under five stress states. The proposed continuum plasticity model was found to accurately predict the multiaxial mechanical response of the material through macroscopic simulations. The microstructure of DP600 contains a relatively soft ferrite matrix and relatively hard martensite particles, suggesting a more complex deformation behavior at the microscale compared to single phase materials. To understand the deformation mechanisms, a representative volume element (RVE) model based on the observed microstructures was built, which was able to predict the macroscopic multiaxial plasticity behavior of the material from the microstructural level. The local deformation inhomogeneity and stress states were also examined through this RVE model. The simulation results showed that in the DP steel studied, closely situated martensite particles increased the local plastic strain and stress triaxiality of the ferrite between them, with no trend for Lode angle parameter.

AB - Multiaxial plasticity behavior of Dual Phase (DP) 600 steel was evaluated through macroscopic testing and predicted through both continuum and micromechanics simulations. The stress state dependent mechanical properties of the material were examined through multiaxial loading under five stress states. The proposed continuum plasticity model was found to accurately predict the multiaxial mechanical response of the material through macroscopic simulations. The microstructure of DP600 contains a relatively soft ferrite matrix and relatively hard martensite particles, suggesting a more complex deformation behavior at the microscale compared to single phase materials. To understand the deformation mechanisms, a representative volume element (RVE) model based on the observed microstructures was built, which was able to predict the macroscopic multiaxial plasticity behavior of the material from the microstructural level. The local deformation inhomogeneity and stress states were also examined through this RVE model. The simulation results showed that in the DP steel studied, closely situated martensite particles increased the local plastic strain and stress triaxiality of the ferrite between them, with no trend for Lode angle parameter.

UR - http://www.scopus.com/inward/record.url?scp=85042720512&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=85042720512&partnerID=8YFLogxK

U2 - 10.1016/j.msea.2018.02.078

DO - 10.1016/j.msea.2018.02.078

M3 - Article

AN - SCOPUS:85042720512

VL - 721

SP - 168

EP - 178

JO - Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing

JF - Materials Science & Engineering A: Structural Materials: Properties, Microstructure and Processing

SN - 0921-5093

ER -