Performance characterization of hybrid rocket fuel grains with complex port geometries fabricated using rapid prototyping technology

Derrick Armold, J. Eric Boyer, Brendan R. McKnight, John D. DeSain, J. K. Fuller, Kenneth K. Kuo, B. Brady, T. Curtiss

Research output: Contribution to journalArticle

3 Citations (Scopus)

Abstract

Rapid prototyping has developed to the point that it can be used to print solid-fuel grains for hybrid rockets. Multijet modeling has been used by The Aerospace Corporation to print composite cell structures of acrylic filled with paraffin wax, allowing for both structural strength and fast regression rate. Grains of this kind show promise for applications such as small satellite or CubeSat thrusters. These grains, among other printed and cast designs, have been tested in the long grain center-perforated (LGCP) hybrid rocket motor at The Pennsylvania State University. Parameters such as chamber pressure, regression rate, and combustion efficiency were calculated to characterize each solid-fuel grain geometry. Focus was placed on designs in which swirl is induced within the grain through printed channels or vanes, but grains with swirl induced through oxidizer injection were also tested as a means of comparison and to further characterize the LGCP injectors. An experimental reduction technique was developed in SolidWorks to characterize regression rate and oxidizer mass flux for complex port geometries, which would otherwise be impossible to determine using conventional methods. Composite honeycomb grains were found to have regression rates comparable to cast paraffin wax standards and, depending on cell size, potentially much higher combustion efficiency. Swirl injection has been shown to produce increases of fuel regression rate around 30% in pure cast paraffin and 40% in cast paraffin with the addition of aluminum particles. In addition, grains containing turbulator vanes were shown to have regression rate enhancements similar to those of straight-port grains subjected to swirl injection.

Original languageEnglish (US)
Pages (from-to)287-307
Number of pages21
JournalInternational Journal of Energetic Materials and Chemical Propulsion
Volume13
Issue number4
DOIs
StatePublished - Jan 1 2014

Fingerprint

Rapid prototyping
Rockets
Geometry
Paraffin waxes
Paraffin
Paraffins
Rocket engines
Composite materials
Aluminum
Acrylics
Mass transfer
Satellites

All Science Journal Classification (ASJC) codes

  • Materials Science(all)

Cite this

Armold, Derrick ; Boyer, J. Eric ; McKnight, Brendan R. ; DeSain, John D. ; Fuller, J. K. ; Kuo, Kenneth K. ; Brady, B. ; Curtiss, T. / Performance characterization of hybrid rocket fuel grains with complex port geometries fabricated using rapid prototyping technology. In: International Journal of Energetic Materials and Chemical Propulsion. 2014 ; Vol. 13, No. 4. pp. 287-307.
@article{eb1cb48c42e14030b09297c331c6da33,
title = "Performance characterization of hybrid rocket fuel grains with complex port geometries fabricated using rapid prototyping technology",
abstract = "Rapid prototyping has developed to the point that it can be used to print solid-fuel grains for hybrid rockets. Multijet modeling has been used by The Aerospace Corporation to print composite cell structures of acrylic filled with paraffin wax, allowing for both structural strength and fast regression rate. Grains of this kind show promise for applications such as small satellite or CubeSat thrusters. These grains, among other printed and cast designs, have been tested in the long grain center-perforated (LGCP) hybrid rocket motor at The Pennsylvania State University. Parameters such as chamber pressure, regression rate, and combustion efficiency were calculated to characterize each solid-fuel grain geometry. Focus was placed on designs in which swirl is induced within the grain through printed channels or vanes, but grains with swirl induced through oxidizer injection were also tested as a means of comparison and to further characterize the LGCP injectors. An experimental reduction technique was developed in SolidWorks to characterize regression rate and oxidizer mass flux for complex port geometries, which would otherwise be impossible to determine using conventional methods. Composite honeycomb grains were found to have regression rates comparable to cast paraffin wax standards and, depending on cell size, potentially much higher combustion efficiency. Swirl injection has been shown to produce increases of fuel regression rate around 30{\%} in pure cast paraffin and 40{\%} in cast paraffin with the addition of aluminum particles. In addition, grains containing turbulator vanes were shown to have regression rate enhancements similar to those of straight-port grains subjected to swirl injection.",
author = "Derrick Armold and Boyer, {J. Eric} and McKnight, {Brendan R.} and DeSain, {John D.} and Fuller, {J. K.} and Kuo, {Kenneth K.} and B. Brady and T. Curtiss",
year = "2014",
month = "1",
day = "1",
doi = "10.1615/IntJEnergeticMaterialsChemProp.2014011169",
language = "English (US)",
volume = "13",
pages = "287--307",
journal = "International Journal of Energetic Materials and Chemical Propulsion",
issn = "2150-766X",
publisher = "Begell House Inc.",
number = "4",

}

Performance characterization of hybrid rocket fuel grains with complex port geometries fabricated using rapid prototyping technology. / Armold, Derrick; Boyer, J. Eric; McKnight, Brendan R.; DeSain, John D.; Fuller, J. K.; Kuo, Kenneth K.; Brady, B.; Curtiss, T.

In: International Journal of Energetic Materials and Chemical Propulsion, Vol. 13, No. 4, 01.01.2014, p. 287-307.

Research output: Contribution to journalArticle

TY - JOUR

T1 - Performance characterization of hybrid rocket fuel grains with complex port geometries fabricated using rapid prototyping technology

AU - Armold, Derrick

AU - Boyer, J. Eric

AU - McKnight, Brendan R.

AU - DeSain, John D.

AU - Fuller, J. K.

AU - Kuo, Kenneth K.

AU - Brady, B.

AU - Curtiss, T.

PY - 2014/1/1

Y1 - 2014/1/1

N2 - Rapid prototyping has developed to the point that it can be used to print solid-fuel grains for hybrid rockets. Multijet modeling has been used by The Aerospace Corporation to print composite cell structures of acrylic filled with paraffin wax, allowing for both structural strength and fast regression rate. Grains of this kind show promise for applications such as small satellite or CubeSat thrusters. These grains, among other printed and cast designs, have been tested in the long grain center-perforated (LGCP) hybrid rocket motor at The Pennsylvania State University. Parameters such as chamber pressure, regression rate, and combustion efficiency were calculated to characterize each solid-fuel grain geometry. Focus was placed on designs in which swirl is induced within the grain through printed channels or vanes, but grains with swirl induced through oxidizer injection were also tested as a means of comparison and to further characterize the LGCP injectors. An experimental reduction technique was developed in SolidWorks to characterize regression rate and oxidizer mass flux for complex port geometries, which would otherwise be impossible to determine using conventional methods. Composite honeycomb grains were found to have regression rates comparable to cast paraffin wax standards and, depending on cell size, potentially much higher combustion efficiency. Swirl injection has been shown to produce increases of fuel regression rate around 30% in pure cast paraffin and 40% in cast paraffin with the addition of aluminum particles. In addition, grains containing turbulator vanes were shown to have regression rate enhancements similar to those of straight-port grains subjected to swirl injection.

AB - Rapid prototyping has developed to the point that it can be used to print solid-fuel grains for hybrid rockets. Multijet modeling has been used by The Aerospace Corporation to print composite cell structures of acrylic filled with paraffin wax, allowing for both structural strength and fast regression rate. Grains of this kind show promise for applications such as small satellite or CubeSat thrusters. These grains, among other printed and cast designs, have been tested in the long grain center-perforated (LGCP) hybrid rocket motor at The Pennsylvania State University. Parameters such as chamber pressure, regression rate, and combustion efficiency were calculated to characterize each solid-fuel grain geometry. Focus was placed on designs in which swirl is induced within the grain through printed channels or vanes, but grains with swirl induced through oxidizer injection were also tested as a means of comparison and to further characterize the LGCP injectors. An experimental reduction technique was developed in SolidWorks to characterize regression rate and oxidizer mass flux for complex port geometries, which would otherwise be impossible to determine using conventional methods. Composite honeycomb grains were found to have regression rates comparable to cast paraffin wax standards and, depending on cell size, potentially much higher combustion efficiency. Swirl injection has been shown to produce increases of fuel regression rate around 30% in pure cast paraffin and 40% in cast paraffin with the addition of aluminum particles. In addition, grains containing turbulator vanes were shown to have regression rate enhancements similar to those of straight-port grains subjected to swirl injection.

UR - http://www.scopus.com/inward/record.url?scp=84908106052&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84908106052&partnerID=8YFLogxK

U2 - 10.1615/IntJEnergeticMaterialsChemProp.2014011169

DO - 10.1615/IntJEnergeticMaterialsChemProp.2014011169

M3 - Article

AN - SCOPUS:84908106052

VL - 13

SP - 287

EP - 307

JO - International Journal of Energetic Materials and Chemical Propulsion

JF - International Journal of Energetic Materials and Chemical Propulsion

SN - 2150-766X

IS - 4

ER -