Stability of elastomeric and lead-rubber seismic isolation bearings

Jared Weisman, Gordon Patrick Warn

Research output: Contribution to journalArticle

45 Citations (Scopus)

Abstract

Elastomeric and lead-rubber bearings are two commonly used types of seismic isolation devices. During seismic events, some of the bearings in an isolation system will be subjected to large axial compressive loads, caused by gravity plus overturning forces, accompanied by simultaneous large lateral displacements. However, the critical load capacity of elastomeric bearings has been shown to reduce with increasing lateral displacement. The design of isolation systems composed of these types of bearings therefore requires that stability at the maximum displacement be demonstrated. The current procedure to assess the stability uses a ratio of areas, referred to as the overlapping area method, to determine the critical load capacity at a given lateral displacement that must be greater than a combination of axial forces imposed on the bearing. Although the overlapping area method provides a simple means of calculating the critical load at a given lateral displacement, it lacks a rigorous theoretical basis and has not been experimentally verified for bearings with shape factors representative of those used for seismic isolation (i.e.,10-30) or for lead-rubber bearings. Experimental testing and detailed nonlinear finite element analysis were employed to investigate the critical load capacities of an elastomeric bearing and a lead-rubber bearing with shape factors of 10 and 12, respectively, at large lateral displacements. The results of these investigations showed the lead core has a negligible effect on the critical load over a range of lateral displacements corresponding to 150-280% shear strain in comparison with the elastomeric bearing. The overlapping area method is shown to conservatively estimate the critical load capacity of this bearing in comparison with the experimental results.

Original languageEnglish (US)
Pages (from-to)215-223
Number of pages9
JournalJournal of Structural Engineering
Volume138
Issue number2
DOIs
StatePublished - Feb 1 2012

Fingerprint

Bearings (structural)
Rubber
Lead
elastomeric
Shear strain

All Science Journal Classification (ASJC) codes

  • Civil and Structural Engineering
  • Building and Construction
  • Materials Science(all)
  • Mechanics of Materials
  • Mechanical Engineering

Cite this

@article{df4e2848a1134a93b3824e2781f0383a,
title = "Stability of elastomeric and lead-rubber seismic isolation bearings",
abstract = "Elastomeric and lead-rubber bearings are two commonly used types of seismic isolation devices. During seismic events, some of the bearings in an isolation system will be subjected to large axial compressive loads, caused by gravity plus overturning forces, accompanied by simultaneous large lateral displacements. However, the critical load capacity of elastomeric bearings has been shown to reduce with increasing lateral displacement. The design of isolation systems composed of these types of bearings therefore requires that stability at the maximum displacement be demonstrated. The current procedure to assess the stability uses a ratio of areas, referred to as the overlapping area method, to determine the critical load capacity at a given lateral displacement that must be greater than a combination of axial forces imposed on the bearing. Although the overlapping area method provides a simple means of calculating the critical load at a given lateral displacement, it lacks a rigorous theoretical basis and has not been experimentally verified for bearings with shape factors representative of those used for seismic isolation (i.e.,10-30) or for lead-rubber bearings. Experimental testing and detailed nonlinear finite element analysis were employed to investigate the critical load capacities of an elastomeric bearing and a lead-rubber bearing with shape factors of 10 and 12, respectively, at large lateral displacements. The results of these investigations showed the lead core has a negligible effect on the critical load over a range of lateral displacements corresponding to 150-280{\%} shear strain in comparison with the elastomeric bearing. The overlapping area method is shown to conservatively estimate the critical load capacity of this bearing in comparison with the experimental results.",
author = "Jared Weisman and Warn, {Gordon Patrick}",
year = "2012",
month = "2",
day = "1",
doi = "10.1061/(ASCE)ST.1943-541X.0000459",
language = "English (US)",
volume = "138",
pages = "215--223",
journal = "Journal of Structural Engineering",
issn = "0733-9445",
publisher = "American Society of Civil Engineers (ASCE)",
number = "2",

}

Stability of elastomeric and lead-rubber seismic isolation bearings. / Weisman, Jared; Warn, Gordon Patrick.

In: Journal of Structural Engineering, Vol. 138, No. 2, 01.02.2012, p. 215-223.

Research output: Contribution to journalArticle

TY - JOUR

T1 - Stability of elastomeric and lead-rubber seismic isolation bearings

AU - Weisman, Jared

AU - Warn, Gordon Patrick

PY - 2012/2/1

Y1 - 2012/2/1

N2 - Elastomeric and lead-rubber bearings are two commonly used types of seismic isolation devices. During seismic events, some of the bearings in an isolation system will be subjected to large axial compressive loads, caused by gravity plus overturning forces, accompanied by simultaneous large lateral displacements. However, the critical load capacity of elastomeric bearings has been shown to reduce with increasing lateral displacement. The design of isolation systems composed of these types of bearings therefore requires that stability at the maximum displacement be demonstrated. The current procedure to assess the stability uses a ratio of areas, referred to as the overlapping area method, to determine the critical load capacity at a given lateral displacement that must be greater than a combination of axial forces imposed on the bearing. Although the overlapping area method provides a simple means of calculating the critical load at a given lateral displacement, it lacks a rigorous theoretical basis and has not been experimentally verified for bearings with shape factors representative of those used for seismic isolation (i.e.,10-30) or for lead-rubber bearings. Experimental testing and detailed nonlinear finite element analysis were employed to investigate the critical load capacities of an elastomeric bearing and a lead-rubber bearing with shape factors of 10 and 12, respectively, at large lateral displacements. The results of these investigations showed the lead core has a negligible effect on the critical load over a range of lateral displacements corresponding to 150-280% shear strain in comparison with the elastomeric bearing. The overlapping area method is shown to conservatively estimate the critical load capacity of this bearing in comparison with the experimental results.

AB - Elastomeric and lead-rubber bearings are two commonly used types of seismic isolation devices. During seismic events, some of the bearings in an isolation system will be subjected to large axial compressive loads, caused by gravity plus overturning forces, accompanied by simultaneous large lateral displacements. However, the critical load capacity of elastomeric bearings has been shown to reduce with increasing lateral displacement. The design of isolation systems composed of these types of bearings therefore requires that stability at the maximum displacement be demonstrated. The current procedure to assess the stability uses a ratio of areas, referred to as the overlapping area method, to determine the critical load capacity at a given lateral displacement that must be greater than a combination of axial forces imposed on the bearing. Although the overlapping area method provides a simple means of calculating the critical load at a given lateral displacement, it lacks a rigorous theoretical basis and has not been experimentally verified for bearings with shape factors representative of those used for seismic isolation (i.e.,10-30) or for lead-rubber bearings. Experimental testing and detailed nonlinear finite element analysis were employed to investigate the critical load capacities of an elastomeric bearing and a lead-rubber bearing with shape factors of 10 and 12, respectively, at large lateral displacements. The results of these investigations showed the lead core has a negligible effect on the critical load over a range of lateral displacements corresponding to 150-280% shear strain in comparison with the elastomeric bearing. The overlapping area method is shown to conservatively estimate the critical load capacity of this bearing in comparison with the experimental results.

UR - http://www.scopus.com/inward/record.url?scp=84858389230&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84858389230&partnerID=8YFLogxK

U2 - 10.1061/(ASCE)ST.1943-541X.0000459

DO - 10.1061/(ASCE)ST.1943-541X.0000459

M3 - Article

AN - SCOPUS:84858389230

VL - 138

SP - 215

EP - 223

JO - Journal of Structural Engineering

JF - Journal of Structural Engineering

SN - 0733-9445

IS - 2

ER -